The F4 flight control with MPU6000 has faster acceleration response; it integrates 5V/2A BEC and integrates OSD.
Input voltage 2S-4S, with BEC-5V output 2A current,
Support mainstream SBUS, DSM2/DSMX, IBUS and other receivers on the market.
There is LED_STRIP interface, active buzzer interface.
When SBUS/IBUS, DSM receiver input, please configure RX2 as input interface.
Factory firmware: betaflight_X.X.X_MATEKF411.HEX
Sensor: MPU6000 three-axis accelerometer / three-axis gyroscope
Power supply: 2-4S battery input
BEC: Built-in 5V/2A
Receiver: Support Sbus or serial RX interface, Spektrum 1024/2048, SBUS, IBUS, etc.
Support for programmable LED_Strip
Built-in voltage detection, alarm
Built-in OSD function, BF online adjustment
Dimensions: 20*20MM, screw hole distance 16*16MM, M2
BS-13A 4-in-1 ESC
13A 4 IN 1 through machine BLHELI_S ESC uses high TGPCB sheet, six-layer board design, open blind buried hole, internal and external copper thickness reaches 2OZ, overcurrent capability is very strong, support 2S-4S voltage flight, single ESC current lasts until 13A (peak 15A 3 seconds), the processor uses EFM8BB2F16G, independent motor drive chip, high integration and stable performance.
1. Input voltage: 2-4S LiPo/2-4S HV LiPo
2, BEC output: no
3, a single ESC continuous working current: 13A * 4 (maximum current: 15A 3 seconds)
4, shape ESC size: 21 * 24mm (including the maximum size of the pad and protruding points)
5, screw hole distance 16*16MM, aperture 2MM
6, weight: 2.9 grams
7, firmware: BLHELI_S G_H_30_REV16_7.HEX
8, support Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
SIVTX-5840 25-100-200MW power adjustable OSD tuning 40CH 5.8G Transmiter
The SIVTX-5840 series is transmitted as a 5.8G ISM band analog image transmission. It has stable output power, long transmission distance and strong power supply filtering. It can ensure that the image has no snowflake and no horizontal stripes under the maximum throttle. Adopting stackable installation, the M2 mainstream flight control with 16*16MM design uses screw holes, and the picture transmission and the same fixed hole position perfectly fit the upper part of the flight control, improving the space utilization of the rack and higher safety. The tower structure can be assembled arbitrarily. The picture adopts the flight control OSD (TXD) signal to control the transmission frequency (IRC Tramp), and only needs to connect any TXD (serial port transmission) of the flight control to the RXD (serial port reception) of the picture transmission, and also The function of manual button switching is retained. Support PIT mode tuning.
1. The output power is stable and the transmission distance is long.
2. Fast 3-speed power switching, independent two red indicators, indicating the current transmitting power of 25/100/200MW.
3. The frequency point uses 4*3 LEDs to display 40 channel values.
4, support OSD remote tuning (IRC Tramp), support PIT mode tuning, can only be opened in the OSD.
5, small size, the antenna uses IPEX interface, reducing the footprint of the PCB board.
6, small size: 20mm * 20mm, mounting holes 16mm * 16mm.
7, light weight: 1.7g
1, input voltage: DC 4.5-5.2V
2. Input current: 200MW = 400 MA
3, power switching: third gear 25MW, 100MW, 200MW
4, signal channel: 40
5, frequency switching: manual button / OSD (IRC Tramp) (simultaneous support)
6, antenna interface: IPEX
7, Dimensions: 20MM*20MM Pitch: 16*16MM, M2
GND power supply negative
+5V power supply positive
VIDEO camera video input
RXD flight control serial transmission